ABL8RPS24100

Configured for regulated 24 VDC auxiliary power generation in industrial automation control circuits, the Schneider Electric ABL8RPS24100 (ABL8RPS24100 Power Supply) provides direct AC-to-DC conversion with adjustable output voltage, overload protection, and DIN-rail mounting.

Hardware Specifications

Parameter	Specification
Model	ABL8RPS24100
Brand	Schneider Electric
Product Series	Modicon Power Supply / Phaseo
Product Type	Regulated switch mode power supply
Origin	Philippines (PH)
Input Voltage	100-120 VAC single phase; 200-500 VAC phase to phase
Output Voltage	24 VDC adjustable to 24-28.8 VDC
Rated Output Current	10 A
Rated Power	240 W
Temporary Current Boost	150% of nominal current for 4 s
Efficiency	87%
Inrush Current	30 A
Power Factor	0.68 at 240 VAC; 0.69 at 120 VAC
Power Dissipation	31 W
Input Harmonic Control	Low-frequency harmonic current filter; IEC 61000-3-2 PFC
Output Protection	Overload, overvoltage, short-circuit, undervoltage, thermal
Overvoltage Protection	30-32 VDC, manual reset
Undervoltage Protection	Trip below 21.6 VDC
Dielectric Strength	3500 V input-ground; 4000 V input-output; 500 V output-ground
Mounting	35 x 7.5 mm or 35 x 15 mm symmetrical DIN rail
Operating Position	Vertical
Dimensions	145 mm D x 125 mm H x 86 mm W
Weight	1 kg
Operating Temp	-25 to 50 deg C without derating; 50 to 60 deg C with derating
Maximum Operating Altitude	2000 m
Protection Degree	IP20
Status Indication	Front LED diagnostics
Connections	Screw terminals and removable screw terminal block
Power Supply Standards	UL 508; CSA C22.2 No 60950-1; EN/IEC 62368-1
Certifications	CCSAus, EAC, KC, RCM, UL

Power Conditioning and Industrial Control Interface

The ABL8RPS24100 incorporates a power factor correction filter for input current harmonic control and provides an adjustable 24-28.8 VDC output. The output can be connected in parallel or series configurations. Front-mounted LED indicators provide output voltage and output current status.

The protection circuitry monitors overload, short-circuit, overvoltage, undervoltage, and thermal conditions. Automatic reset is provided for specified short-duration fault conditions, while the overvoltage protection is specified for 30-32 VDC with manual reset.

The unit uses DIN-rail mounting and a vertical operating position. Input, output, and grounding connections use screw-type terminals with conductor ranges specified by the manufacturer. The electrical separation is rated at 4000 V between input and output.

Frequently Asked Questions

Q: What output voltage range can be adjusted on the ABL8RPS24100?

A: The output is rated at 24 VDC and can be adjusted from 24 to 28.8 VDC.

Q: What temporary overload capability is specified?

A: The power supply can deliver 150% of its nominal output current for 4 s.

Q: What mounting arrangement is specified?

A: The unit mounts vertically on a 35 x 7.5 mm or 35 x 15 mm symmetrical DIN rail.

Field Installation Guidelines

Install the power supply vertically on the specified symmetrical DIN rail and maintain the manufacturer's required ventilation clearance around the enclosure. Verify the AC input configuration before energization because the input terminals support different single-phase and phase-to-phase voltage ranges.

Connect protective grounding through the designated ground terminal. Separate AC input wiring from low-voltage DC control wiring where practical to reduce conducted and radiated interference. Use the specified terminal conductor sizes and secure all screw terminals to the manufacturer's installation requirements.

Before connecting downstream automation loads, verify the adjusted DC output voltage. When the output is used for sensitive PLC, I/O, or instrumentation circuits, check the total load current against the 10 A rated output and account for the specified temperature derating above 50 deg C.

---